3Com Network Router 3CRWE454A72 User Manual

About Your Access Point (front)  
Installation Guide  
1
2
3
4
3CRWE454A72  
WLAN  
LAN Status  
Alert  
Power  
11g 11a  
OfficeConnect Wireless 11a / b / g Access Point  
Continuously on – A fault has been detected with your Access Point during  
1
Alert LED orange  
LAN Status LED green (100Mbps link) / yellow (10Mbps link)  
4
the start-up process. Refer to the main User Guide.  
Indicates a number of different conditions, as described below.  
Off – The Access Point is operating normally.  
If the LED is on, the link between the port and the next piece of network  
equipment is OK. If the LED is flashing, the link is OK and data is being  
transmitted or received. If the LED is off, nothing is connected, or the  
connected device is switched off, or there is a problem with the connection  
(refer to the User Guide). The port will automatically adjust to the correct  
speed and duplex.  
2
3
Power LED green  
Flashing quickly – Indicates one of the following conditions:  
Indicates that the Access Point is powered on.  
– the Access Point has just been started up and is running a self-test  
routine  
Wireless LAN (WLAN) Status LED green  
– the administrator has invoked the Reset to Factory Defaults command  
If the LEDs are on it indicates that wireless networking is enabled. If the LED  
is flashing, the link is OK and data is being transmitted or received. If the  
LED is off, the Wireless LAN has been disabled in the Access Point, or there  
is a problem (refer to the User Guide).  
– the system software is in the process of being upgraded  
®
In each of these cases, wait until the Access Point has completed the  
current operation and the alert LED is Off.  
OfficeConnect  
Wireless 11a/b/g Access Point  
(3CRWE454A72)  
Flashing slowly – The Access Point has completed the Reset to Factory  
Defaults process, and is waiting for you to reset the unit. To do this, release  
the reset button and allow the unit to restart. The Access Point will then  
enter the start-up sequence and resume normal operation.  
About Your Access Point (back)  
6
7
5
8
9
5
OK  
Ethernet  
RESET  
5
6
Wireless Antennae  
Ethernet port  
8
The antennae on the product should be placed in a ‘V’ position.  
Using suitable RJ45 cable, you can connect your Access Point to a  
computer, or to any other piece of equipment that has an Ethernet  
connection (for example, a hub or a switch). This port has an automatic  
MDI/MDIX feature, which means either straight-through or a crossover  
cable can be used.  
Power Adapter socket  
Only use the power adapter that is supplied with this Access Point. Do not  
use any other adapter.  
Reset Button  
7
9
Power Adapter OK LED green  
If you want to reset your Access Point to factory default settings, and  
cannot access the web management interface (for example, due to a lost  
password), then you may use this button. Refer to the User Guide for  
further details.  
Indicates that the power adapter is supplying power to the Gateway. If the  
LED is off, there may be a problem with the power adapter or adapter  
cable.  
3Com Corporation, Corporate Headquarters, 350 Campus Drive, Marlborough, MA 01752-3064  
Copyright © 2003 3Com Corporation. All rights reserved. 3Com, the 3Com logo, and OfficeConnect  
are registered trademarks of 3Com Corporation.  
Microsoft, MS-DOS and Windows are registered trademarks of Micorsoft Corporation.  
All other company and product names may be trademarks of their respective companies.  
Part number: DIA0045-4AAA01 Published: December 2003  
 

Abbyy USA Scanner SERVER 32 User Manual
ADC Network Router WorldDSL GS User Manual
AEG Microwave Oven MC2662E User Manual
Allied Telesis Power Supply AT MCF2000AC User Manual
Alpine GPS Receiver NVE M300 User Manual
Alto Shaam Oven 1220ES User Manual
Amana Clothes Dryer 40119701 User Manual
ATN Binoculars NVM14 PT User Manual
Axis Communications Security Camera Q1932E User Manual
Behringer Stereo System XR12 User Manual